![]() If you continue to experience problems, please contact Focusrite Technical Support. To turn the outputs grey in MixControl, simply hold down the SHIFT key on your keyboard while clicking on them. It appears I can only control the headphone outputs (both of them) by using them in conjunction with the main monitor out meaning if the main monitor control. However please exercise caution as any signal coming out of the corresponding line outputs will be very loud. Grey outputs will output audio at full volume, and so having the headphone outputs set to Grey will mean that utilising just the headphone output level control should give sufficient level to the headphones.If using the headphone outputs set to Blue, ensure that the monitor level is nice and high. Tested on: macOS 10.15 (Catalina) macOS 10.14 (Mojave) macOS 10.13 (High Sierra) macOS 10.12 (Sierra) macOS 10.12 or later is required to run Saffire Mix Control 3.9. It is possible to have the headphone outputs set to ‘Blue’, yet still not hear audio as there isn’t sufficient level. This will be the last software release for the Saffire range as they are now discontinued, please see this article from our Help Centre. Blue outputs will pass audio, but the level of the output is dependent on the position of the monitor level control.For audio to be heard from the headphone outputs, the corresponding line outputs must not be set to Red. The problem is that, with windows 10, the second unit does not stably locked with the first one. If you were doing all the routing within your DAW, there. In windows 7 everythings works perfectly. In essence, you can send anything to anything within MixControl and it all gets send virtually delay free. Red outputs are muted and won’t pass any audio. I'm working with 2 saffire pro 40 in dual unit on a Dell E6530 laptop with a pcmcia Firewire card (ExpressCard with a Texas Instrument chipset). Saffire MixControl, the ultra-low-latency 18 x 8 DSP mixer/router software provided with Saffire PRO 24 sets a new standard for audio interface control.This is done in the Monitor section of Saffire MixControl, shown below.Īs demonstrated by the image above, the monitor outputs have three states, signified by three different colours, Red, Blue, and Grey. ![]() It is then necessary to ensure that sufficient level is being sent out of the headphone outputs to the headphones. It is worth noting that most computer audio software will send audio out of DAW 1 (Left Channel) and DAW 2 (Right Channel) by default. Select from the choice of Inputs, DAW (computer) Outputs, and Mixes by clicking in the box next to the relevant output, and route audio to the headphones. In the example above (of a Saffire Pro 24 DSP), Headphone Output 1 (on the Saffire hardware) is a copy of Line Outputs 3&4, and Headphone Output 2 (on the Saffire hardware) is a copy of Line Outputs 5&6. These outputs are marked by the headphone symbol ( ) in the routing section of Saffire MixControl, as shown below. The H/W Control button (Saffire PRO 40, Liquid Saffire 56 and Scarlett 18i20 only) links the position of the monitor dial in the MixControl software to the position of the monitor level control on the front of the Saffire hardware.The headphone outputs from Saffire MixControl are copies of specific line outputs on the rear of the interface, so it is important to ensure that you’re routing audio to the correct outputs. However, all of these presets can be configured manually using the method described above. The Monitor Preset… button allows you to select a variety of preset speaker configurations, more information about which can be found on your product’s download's page. Care should be exercised so as not to damage any audio equipment connected to these outputs, as the audio will be very loudĬlicking on the individual outputs toggles them between blue and red, whereas holding down the SHIFT button on your keyboard and clicking will turn the output grey/silver. ![]() Grey/Silver outputs are active and will output any audio at full volume, regardless of the position of the monitor level dial.Blue outputs are active, and their level is controlled by the monitor level dial in the MixControl software (shown in the screenshot above).Red outputs are muted, and no audio will be passed from them.They will either beRed, Blue, or Grey/Silver. This is achieved in the monitor section of MixControl, shown below:Ībove the Monitor Preset… button in the monitoring section of Saffire MixControl, you will be able to see numbered boxes corresponding to the line (analogue) outputs on your unit. Once you have configured your mixes and routed audio to the outputs of your Saffire (see Part I and Part II of this tutorial), you need to ensure that a sufficient level is getting to your chosen outputs. ![]() ![]() Applies to: Saffire Range and 1st Generation Scarlett 6i6, 8i6, 18i6, 18i8 and 18i20 ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |